Skip to main content
This guide covers RADR’s settings menu, WiFi configuration, and power management options.

​
Accessing Settings

From the main menu, select Settings to access the settings menu.

​
Settings Menu Options

OptionDescription
Go BackReturn to the main menu
WiFi SettingsConfigure WiFi network connection
Update DeviceCheck for and install firmware updates
Restart DeviceReboot the RADR
  • Right Encoder — Scroll through options
  • Right Button — Select the highlighted option
  • Left Button — Return to main menu

​
WiFi Configuration

WiFi connectivity enables over-the-air (OTA) firmware updates for your RADR.
WiFi is optional and primarily used for firmware updates. RADR’s core functionality (device control) works entirely over Bluetooth.

​
Setting Up WiFi

1

Open WiFi Settings

From the settings menu, select WiFi Settings.
2

Connect to RADR's Access Point

RADR creates a WiFi access point called “OSSM Remote Setup”.A QR code is displayed on screen for easy connection:
WIFI:S:OSSM Remote Setup;T:nopass;;
Scan the QR code with your phone, or manually connect to the network:
  • Network Name: OSSM Remote Setup
  • Password: None (open network)
3

Configure WiFi Credentials

Once connected to RADR’s access point, a configuration portal opens automatically:
  1. Select your home WiFi network from the list
  2. Enter your WiFi password
  3. Save the configuration
4

Confirmation

After successful configuration, you’ll see the “WiFi Connected” screen:
  • Message: “Your OSSM Remote is now connected to WiFi.”
  • RADR is now ready to receive OTA updates

​
WiFi Configuration Details

ParameterValue
Access Point NameOSSM Remote Setup
SecurityOpen (no password)
Portal Timeout30 seconds
Retry Attempts5
The WiFi setup portal has a 30-second timeout. If the portal times out, restart the WiFi Settings process.

​
Update Device

Select Update Device to check for and install firmware updates.
This feature requires WiFi to be configured. Updates are downloaded and installed over-the-air.

​
Restart Device

Select Restart Device to reboot your RADR. This is useful for:
  • Clearing temporary issues
  • Applying certain settings changes
  • Resetting the Bluetooth state
The device will power off and restart automatically.

​
Sleep Mode

From the main menu, select Sleep to enter deep sleep mode.

​
What Happens in Sleep Mode

  1. RADR disconnects any connected devices
  2. A shutdown sound plays
  3. The display turns off
  4. LEDs turn off
  5. The device enters ultra-low power mode

​
Waking from Sleep

Press any of the three under-screen buttons to wake RADR:
  • Left button
  • Middle button
  • Right button
When waking from sleep, RADR performs a full restart and returns to the main menu.

​
When to Use Sleep Mode

Use sleep mode when:
  • You’re done using RADR but don’t want to fully power off
  • You want to conserve battery between sessions
  • You want a quick way to pause without disconnecting the power switch
For extended storage, use the physical power switch instead of sleep mode. Sleep mode still consumes minimal power.

​
Power Management Summary

MethodBattery UsageWake Method
Active (connected)HighN/A
Active (idle)MediumN/A
Sleep ModeVery LowUnder-screen button
Power Switch OffNonePower switch

​
Troubleshooting

  • Ensure you’re connected to the “OSSM Remote Setup” network
  • Try opening a browser and navigating to 192.168.4.1
  • Wait a few seconds after connecting
  • Restart WiFi Settings if the portal timed out
  • Verify your WiFi password is correct
  • Ensure your router is within range
  • RADR supports 2.4GHz networks only
  • Try moving closer to your router
  • Ensure WiFi is connected and working
  • Check that RADR has sufficient battery
  • Try the update again
  • Contact support if updates consistently fail
  • Press and hold an under-screen button for 2-3 seconds
  • If unresponsive, toggle the power switch off and on
  • Ensure RADR has battery charge